Storage and handling

Lyophilized peptides are stable for a long time and fragile for a short one. Almost everything that ruins a vial happens in the ten minutes around reconstitution, or in the weeks after it.

TEMPERATURE

Two different materials, two different rules.

A sealed lyophilized vial and a reconstituted one behave nothing alike. The dry powder is a stable solid; the solution is a protein in water, slowly hydrolysing from the moment it dissolves.

STATECONDITIONSWORKING WINDOW
Lyophilized, sealed −20 °C, desiccated, protected from light Months to years. The COA states the retest date for your specific lot — go by that, not a general figure.
Lyophilized, short term 2–8 °C, desiccated Weeks. Acceptable for material in active use. Not where long-term stock should live.
Reconstituted 2–8 °C, protected from light, not frozen Roughly 28 days is the common working assumption across the literature, and it varies by compound and diluent. The supplier's stated beyond-use date governs.
Anything at room temperature Transit and bench time only Hours. Brief excursions during shipping are expected and accounted for. Prolonged ambient storage is not.

DILUENT SELECTION

The preservative is the whole difference.

Bacteriostatic water is sterile water with roughly 0.9% benzyl alcohol added as a preservative. That alcohol is what allows a vial to be entered more than once without becoming a culture medium — which is why multi-entry work uses it and single-entry work often doesn't.

DILUENTCOMPOSITIONNOTES
Bacteriostatic water Sterile water + ~0.9% benzyl alcohol The default for material that will be entered repeatedly over days or weeks. The preservative sets the practical beyond-use window.
Sterile water for injection Water, no preservative No bacteriostatic protection, so it offers no multi-entry window. A handful of compounds are incompatible with benzyl alcohol and call for it specifically.
0.9% sodium chloride Isotonic saline Compatible with some peptides and not others; a few will precipitate at physiological ionic strength. Check the compound before assuming.
Acetic acid, dilute Typically 0.1–1% Used for poorly soluble sequences that won't go into neutral water. A solubility question, not a default.

RECONSTITUTION

Slow, down the wall, and never shaken.

The mechanical part matters more than people expect. Peptides are denatured by shear and by the air-water interface, and a vigorous shake supplies both at once.

1

Let the vial reach room temperature

Taking a vial straight from −20 °C and opening it draws condensation onto cold glass and into the powder. Water is what you're trying to control — let the vial equilibrate before the stopper comes off.

2

Calculate the diluent volume first

Decide the concentration before you touch anything, not while holding a loaded syringe. The volume determines how fine your measurements can be downstream, and it can't be undone once the water is in.

3

Swab both stoppers with 70% isopropyl and let them dry

Both the peptide vial and the diluent vial. Let the alcohol evaporate rather than wiping it off — the drying is what does the work, and a wet stopper carries alcohol into the vial.

4

Inject the diluent against the glass wall

Angle the needle so the stream runs down the inside of the vial rather than jetting directly onto the powder cake. A direct jet foams the solution and drives peptide into the air-water interface, where it denatures.

5

Let it dissolve undisturbed, then swirl gently

Most lyophilized peptides go into solution on their own within a few minutes. If it needs help, roll or swirl the vial slowly. Never shake, never vortex, and don't invert it repeatedly — visible foam means you have already lost material.

6

Inspect against a light background

Most solutions should be clear and colourless; GHK-Cu is a notable exception and is deep blue. Cloudiness, visible particulates, fibres or persistent foam are all reasons to stop and reassess rather than proceed.

7

Label the vial before it goes in the fridge

Compound, concentration in mg/mL, the date you reconstituted it, and the beyond-use date. An unlabelled vial in a shared fridge is an unidentifiable vial within a week, and concentration is impossible to recover by inspection.

The calculator does step two.

Enter the labeled mass and the diluent volume and it returns the exact graduation, plus how precisely that mix can actually be measured on your barrel.

Open the calculator

WHAT ACTUALLY GOES WRONG

Five failures, in rough order of frequency.

Milligrams read as micrograms

The thousandfold error. It happens because labels, literature and calculators mix the two units freely, and 0.25 mg and 250 mcg are the same quantity written two ways.

Fix: work in one unit throughout, and sanity-check the result against the vial's total mass.
Salt mass mistaken for peptide mass

Some labels state the mass of the salt form — acetate or trifluoroacetate — rather than net peptide. The difference can be a meaningful fraction, and every downstream calculation inherits it.

Fix: confirm on the COA whether the stated mass is net peptide content.
Shaking instead of swirling

Shear forces and the air-water interface both denature peptides. Foam is the visible symptom; the loss happens whether or not you see it.

Fix: swirl or roll slowly, and wait. Time dissolves more than agitation does.
Freeze-thaw cycling of reconstituted material

Each cycle concentrates solutes at the ice front and drives aggregation. A solution frozen and thawed repeatedly degrades far faster than one simply refrigerated.

Fix: refrigerate reconstituted material, don't freeze it. If long storage is required, aliquot once and freeze the aliquots.
Over-dilution past measurable precision

Less common but silent. Too little diluent puts the target draw at one or two units on the barrel, where half a unit is a large fraction of the quantity and every measurement carries that error.

Fix: check the precision reading in the calculator before committing to a mix.
RESEARCH PURPOSES ONLY

This page describes laboratory handling of research materials. It is not a protocol for use in humans or animals, and nothing here is medical, veterinary or dosing guidance. All compounds are supplied strictly for laboratory research: not drugs, foods, cosmetics or dietary supplements, and not for diagnosis, treatment, cure or prevention of any condition.

Storage figures are general working assumptions. The certificate of analysis for your specific lot governs, and where it differs from anything stated here, follow the certificate. Handling, storage and disposal remain the responsibility of the end user.